Now use the brass “jam” nuts or thin spring steel fastener to secure the “T” bolts and oval washers in place. Take extra care to center the new wax ring over the closet ring flange opening or alternatively, over the outlet on the underside of the bowl. In the majority of cases as the flush button itself is so simple any issues with the toilet flushing will be down to the fact the flush valve has actually failed and needs replacing. Access to public toilets is a matter of hygiene and personal dignity, and we need to make sure we support the needs of all,” he says. “There is no law that compels councils to make such a provision, although they are empowered to do so, and it is not surprising that it has become a victim of cost savings. But some in society are hard-hit; homeless people, those living in rural areas, and in particular people with a disability.” After installing the new flapper, run the dye test again to assure you have no leak. If the leak persists (and every now and then it will), you are probably going to have to replace the entire flush valve. To do this, you will need to turn your water off and disconnect the supply line. Yes it’s not the most cerebral of pursuits, but if you want something silly for the children to play which will make them laugh, and they love a bit of toilet humour, then Toilet Trouble Flushdown will be right up their alley. How much and where to buy

A person with dementia is more likely to have accidents, incontinence or difficulties using the toilet than a person of the same age who doesn’t have dementia.

Toilet refills on its own

Be sure to get the bowl relatively level before tightening anything down. Use a two foot long “carpenters” level placed over the center of the bowl to see if it is level. Once this is accomplished place the plastic “cap” washers (lip up!) over the “T” bolts taking care to cover as much of the oblong holes provided in the base of the toilet as possible. Problem: You put an object in the tank to displace water and save money, but it’s affecting flush strength.

not being able to tell someone that they need to go to the toilet because of difficulty communicatingWith the other type the push button is connected to the flush valve through a flexible cable. These are now the more common type of flush mechanism used on push button cisterns as they are much easier to install and connect up. If the water is not creeping up the overflow tube and you continue to hear the toilet cycling, perform the dye test to be sure there is not a flapper leak. If the dye test is positive, then complete the procedure for the replacement of the flapper as described earlier. Noisy toilet One of the most common reasons for the flush on a toilet to stop working is that the actual handle itself becomes detached from the flushing mechanism.

If the chain or wire becomes detached from the syphon or flush handle the flush simply won’t operate. For some people, incontinence develops because messages between the brain and the bladder or bowel don’t work properly. They may not recognise that they have a full bladder or bowel, or be able to control them. Other reasons include: It is not uncommon for system water pressure to rise by 15 to 20 pounds per square inch (psi), and by as much as 30 psi in some situations. This rise in pressure could cause “water creep” inside your gravity-fed tank by one-half of an inch or more. That is why the manufacturers of toilets normally suggest that the water level to be set at approximately one inch below the top of the overflow tube. Water level in the tank Ali Wileman, Chair of the RCN Continence forum, says: “Today and any day you can choose when and where you go to the toilet, even going into a cubicle and choosing to use or not use. What about the individual who requires specialist equipment? For someone who is disabled, the experience of using a disabled toilet is not pleasant, especially if it’s also a facility used by babies and young children. Not all disabled toilets are fit for every disability.”The flush handle itself will be attached to the syphon in one of 2 ways, either by a chain or piece of wire. When the lever is depressed, or the chain pulled (with an older high level cistern pull chain toilet), the flush diaphragm inside the syphon is pulled upwards on the diaphragm frame and this in turn releases water into the bowl. Whatever the design, the fill valve works to automatically open the water supply valve when the water level falls in the tank during a flush, then shuts off automatically when the water level rises to a specific level in the tank. Depending type of design, the valve is operated either by a floating ball or a float cup that moves up and down with the water level in the tank. Floatless fill valves operate by sensing water pressure at the bottom of the tank.