When you are trying to pair your Skullcandy earbuds with your device, make sure you are not placing them too close to each other. Maintain a reasonable distance, and then try pairing them. Perform a soft reset on both devices Furthermore, you will hear a voice command saying, “your device is now pairing,”which means that the earbuds are now looking to pair with your device Although, you do have the option to use only one earbud (left or right side) if you prefer Solo Mode in some situations. The LEFT and RIGHT side earbud can be your master earbud, so either bud can be used in Mono Mode (one earbud listening).

INDY™ EVO has stereo (both bud) calling and streaming so you’ll always hear the caller or your content in both ears. At this time, turn ON your device’s Bluetooth and look for "Dime" in your list of Available Bluetooth devices, and select it. You can’t recharge your earbuds if your Skullcandy Sesh Evo case is not charging. Knowing why your charging case won’t charge can help fix the problem . What is certain about these headphones is that they are unusually small and very light, appearing almost miniaturised and weighing no more than four grams per side. The same applies to the transport case, which serves as a charging station and weighs 26 grams, easily disappears in one hand and can be attached to a key ring via a lanyard. The case is a little difficult to open, as the lid snaps tightly into place and is also held closed by a magnetic catch, which means that the Dime are safely stowed away when out and about and cannot get lost if clipped to a belt loop. The visually striking recesses in the housing surfaces of these in-ears might turn out to be a dust catcher in the long run. However, the earpieces themselves have an IPX4 water- and sweat-resistant finish, which facilitates easy cleaning, makes them suitable for use during sporting activities and offers protection in the rain. It is also practical that the housings are flat enough to fit under a cap, especially since nothing presses and the light weight makes them hardly noticeable when worn. They are sufficiently stable to wear for a jog, but stronger vibrations during sports should be avoided. While paired, you simply touch the LEFT or RIGHT bud 2x and hold for 2 seconds, you will then hear a voice prompt notifying you each time it changes to a new preset EQ. You will cycle through the EQ modes each time you complete the touch 2x and hold for 2 seconds action. The 3 modes are Music Mode, Podcast Mode, and Movie Mode.

GENERAL QUESTIONS

PUSH™ ULTRA has stereo (both bud) calling and streaming so you’ll always hear the caller or your content in both ears. Yes, simply lay your charging case on a wireless charging pad and the LED indicator in the case and on the wireless charging pad will confirm it is charging. Remove your Sesh earbuds from the list of compatible devices in your Bluetooth menu, then turn off your Bluetooth on the currently paired smart device. While paired, you simply press the LEFT or RIGHT bud 4x and you will hear a voice prompt notifying you each time it changes to a new preset EQ. You will cycle through the EQ modes each time you complete the 4x tap. The 3 modes are Music Mode, Podcast Mode, and Movie Mode.

Skullcandy offers some of the most colorful headphones on the market. If you like to match your tech accessories to your outfits, they tend to have several color schemes for each model, including two or three-tone variants and camo/military color schemes. When paired to your device, you can press the LEFT or RIGHT bud 3x to activate your voice assistant feature at any time. Sometimes low battery could be the reason behind pairing issues between two Bluetooth devices. Just make sure you charge your Skullcandy earbuds and the other device ahead of pairing. If one of the devices is undercharged, you might face pairing issues. Remove any previously connected devices Power ON your earbuds by removing them from the charging case, or manually press and hold the button on each bud for 2 seconds. If you’re on a very tight budget, these true wireless earbuds offer better sound quality than you would expect. These are a fantastic buy and would make a good gift as well. Skullcandy Dime review: also considerYour earbuds will flash Red/Blue momentarily as they re-sync, once successful they will flash Blue together and you will hear a “connected” voice prompt. Please note – BOTH the LEFT and RIGHT bud for INDY™ EVO can be used in Solo Mode, this is because the new tech allows you to Use Either Bud Solo. If you have paired your Skullcandy earbuds before, but now they don’t seem to connect, although they keep showing up in the paired devices list. To correct this issue, unpair your Skullcandy earbuds from the list and then try to pair them again with your device. Move away from specific devices in your household To charge your case, plug in the Micro-USB charging cable and connect to a computer, wall charger, power bank or 12-volt adapter in a car.

When pairing to your Sesh®️ Evo, be sure to ONLY select the product name from the available device pairing list (it will appear exactly as "Sesh Evo").*** While the Skullcandy Dime true wireless buds are far from perfect, they are fantastic value for money.To charge your earbuds, place them in the charging case. The earbud LEDs will be solid red while charging. Please note – BOTH the LEFT and RIGHT bud for PUSH™ ULTRA can be used in Solo Mode, this is because the new tech allows you to Use Either Bud Solo. SESH® EVO has stereo calling and streaming so you’ll always hear the caller or your content in both ears.

The charging case LED will flash GREEN when charging, and will remain constant GREEN when fully charged. Now, take out the left earbud from the charging case and tap the center of the earbud around 4 times until you see a red light flash This allows both the LEFT and RIGHT bud to work alone, which allows more media controls and features to be activated from either side, and the microphone to work on either side. Functions such as, play/pause, answer call/hang up call, Activate Assistant, switching between EQ modes, and Ambient Mode can be controlled on both the LEFT and RIGHT bud, simplifying the user experience. The LEFT and RIGHT side earbud can be your Primary earbud, so either bud can be used in Solo Mode (one earbud listening).We’ll provide clear, concise directions for resetting all Skullcandy devices, helping you reconnect your music with ease. We hope this guide helps you understand how to pair Skullcandy wireless earbuds and also how to troubleshoot Skullcandy wireless earbuds. If none of the methods or troubleshooting steps help you pair your wireless earbuds with your device, get in touch with customer support at Skullcandy. Once successfully paired, a voice prompt will notify you are now “Connected” and you will see INDY™ EVO twice in your “paired devices” list. This could be keeping the buds from sitting correctly in the case. If you’re having a hard time closing the lid completely, it is likely because the earbuds are not set correctly or the gels are interfering.